Address your needs quickly by calling 800-926-1926 or 262-692-2416

148-2 Series Twist & Seal Condenser Plugs Sizes: 5/8" to 2"

.

For other mechanical plugs click here

The Twist & Seal Condenser Plugs are economical low pressure plugs designed specifically for heat exchangers that operate at a moderate temperature up to 275 degrees Fahrenheit and pressures of approximately 150 psi.

The Twist & Seal Condenser Plugs are oil resistant and can be installed with only a slotted screwdriver. The Plugs are made of Buna-N Rubber and have a solid brass expanding screw.

 

.condenser plugs

 

Plug Selection Chart

Click an Item Number below for the Web Store

Size Plug Expansion Range

Gauge

 

 Shpg
Wt
lbs		 Item
Number		 Unit
Price
Each
Maximum

Minimum
in in mm in mm
5/8 0.560 14.22 0.500 12.70 18-20g 0.25 148-2063-1820 US $22.45
3/4 0.620 15.75 0.580 14.73 14-16g 0.5 148-2075-1416 US $22.45
3/4 0.700 17.78 0.640 16.26 18-22g 0.5 148-2075-1822 US $22.45
7/8 0.800 20.32 0.700 17.78 14-19g 0.5 148-2088-1419 US $22.45
7/8 0.880 22.35 0.800 20.32 20-22g 0.5 148-2088-2022 US $22.45
1 0.930 23.62 0.880 22.35 14-19g 0.5 148-2100-1419 US $22.45
1 0.980 24.89 0.930 23.62 20-22g 0.5 148-2100-2022 US $22.45
1 1/8 1.050 26.67 0.980 24.89 14-19g 0.5 148-2113-1419 US $22.45
1 1/8 1.120 28.45 1.050 26.67 20-22g 0.5 148-2113-2022 US $22.45
1 1/4 1.210 30.73 1.120 28.45 14-19g 0.5 148-2125-1419 US $31.45
1 1/4 1.270 32.26 1.210 30.73 20-22g 0.5 148-2125-2022 US $31.45
1 1/2 1.428 36.27 1.270 32.26 14-19g 0.5 148-2150-1419 US $35.95
2 1.875 47.63 1.428 36.27 14-19g 0.5 148-2200-1419 US $64.45

 

Condenser Tube Chart (ID)
  14g 15g 16g 17g 18g 19g 20g 22g
5/8" .459 .481 .495 .509 .527 .541 .555 .569
3/4" .584 .606 .620 .634 .652 .666 .680 .694
7/8" .709 .731 .745 .759 .777 .791 .805 .819
1" .834 .856 .870 .884 .902 .916 .930 .944
1 1/8" .959 .985 .995 1.009 1.027 1.041 1.055 1.069
1 1/4" 1.084 1.106 1.120 1.134 1.152 1.166 1.180 1.194
1 1/2" 1.334 1.356 1.370 1.384 1.402 1.416 1.430 1.444
2" 1.834 1.856 1.870 1.884 1.902 1.916 1.930 1.944

 

Installation Instructions

The Twist & Seal Condenser Plug you have chosen should not fit into the condenser tube until the expansion screw is used to reduce the plug diameter.

Remove the end cap by turning to the right. Insert a slotted screwdriver into the expansion screw and turn to the left which will reduce the diameter until the plug fits into the tube ID.

Be sure to wipe the tube ID with a clean cloth so it is dry prior to installation of the plug to ensure a good friction fit.

Insert the Twist & Seal Condenser Plug into the tube with the flange pressing against the tube sheet. Tighten the expansion screw to the right until the plug is seated as tight as possible without strippng the slotted head. Replace the protective end cap onto the expansion screw by turning to the left.

Petersen Terms & Conditions Apply

Price subject to change without notice